Suspension of open evenings

Hi all,

It is with great regret that following current UK government advice, all public open sessions at the makerspace are to be suspended until further notice to limit the spread of COVID-19.

Members may still access the space as usual, however we are looking to setup a reservation system in case any isolation is required.

For more information, please let myself or any of the other directors know via email, Slack or the forum.

Kind Regards



2018 at the Makerspace

Events & Open Evenings

Over the last year we have had various donations of equipment including a Singer sewing machine and Draper band saw. We have enjoyed laser-cutting a whole range of signs, leatherwork and even Arts Council funded  sculptures. Electronics has also featured prominently our group build of dome nodes, modular synthesisers and various digital clocks have gathered a lot of enthusiastic support.

Innovate Guildford – 17th March

This is an annual large technology showcase event held at GLive in Guildford where we demonstrate the wide range of creative projects from the MakerSpace and its community workshop to the general public and ideas, new technologies and knowledge in many stimulating conversations.

Repair Cafe

Organised by Guildford Borough Council to encourage people to repair their broken items and reduce landfill the Repair Cafe has proved very popular. We have enjoyed hosting the event in the Boileroom Garden and venue and seeing the enthusiasm of the attendees as old damaged items are brought back to life. Our additional workshop facilities and expertise helping broaden the range of repairs.

EMF Camp

EMF camp 2018 had the largest SHM village yet with many members, associates and friends. We enjoyed visits from and visited many other groups and makerspaces from the UK and around the world. Our geodesic dome made its second EMF appearance, this year sporting multiple networks of microcontrolled  blinding LEDs and pacmen.

Wireless and CANBus lighting nodes for our geodesic dome and EMF camp laser cut leatherwork.

Hack The Space

In October we had our first Hack the Space. This started with an all round clean up followed by modifying storage, creating more workspace and creative space saving. We plan to follow up with electronics area improvements.


Surrey and Hampshire Makerspace AGM – 22/01/2018 @ 7:30pm

The space’s AGM is happening tonight! Our members will be gathering in the Boileroom venue from 7:30pm onwards to discuss the administration and status of the space.

We’ll have a few guest talk of interest, the bar will be open, and it’ll be a chance to meet up with the members of the space! You’ll also be able to pick up your new membership card for 24/7 access to the makerspace.

If you aren’t a member yet, do feel free to still come along and see what we get up to. Tours of the space are freely available and you can have a chat to current members.


Hope to see you there!


January 19, 2018 – Open Session

Open Session Tomorrow!

Don’t forget our regular open session will be on tomorrow from 6pm onwards! Come join us at the Makerspace whether you’re a member working on a project or a visitor coming to say hi.

Where to Find Us

First time visiting the Space? See our page here on location, parking and public transport for more details.

Our Equipment

We have lots of tools and machines available at the space, from hand tools to computers and soldering irons to laser cutters.
After something specific or want to check? Feel free to drop a note on the Forum post by clicking on the ‘start discussion’ link below.


Do let us know if you have any more questions on the Forum post – we usually announce who’s coming and what time on the post on the day of the session, too. If you’re bringing a project along, tell us – we have a wide variety of interests and someone might be able to help or chat about it.

Hope to see you there!



Upcoming Events

The Surrey & Hampshire Makerspace are involved in a number of interesting events this week, here’s what’s going on:

Repair Cafe / Open Day – Saturday 14th October.
SHM hosts the Repair Cafe at the Boileroom in Guildford. Come along between 10:00 and 12:00 for another chance to bring your household items which are in need of repair and get expert help to fix them!

The Surrey & Hampshire Makerspace will also be having an Open Day between 10am and 3pm for people to come along and visit the space and see what’s going on. So why not pop on down?

16th Egham Jam – Sunday 15th October.
Learn more about the Raspberry Pi computer and see some of the cool things you can do with them, this time with a Halloween twist! The 16th Egham Jam is free but you do need to register on the Eventbrite page.

Let’s Get Making (Basingstoke) – Wednesday 18th October.
Some of our members will also be down in this Wednesday for Let’s Get Making. It’s a chance to learn more about making, meet fellow makers and see some cool projects. It’s hosted by Basingstoke Makerspace, it’s FREE and starts at 7pm.

Open Evenings
Plus we’ll still be hosting our regular open evenings this Tuesday and Friday at our space above the Boileroom from 6pm!


Planning, Polycarbonate, and Programming

A broken dress strap adjustment slider and the replacement cut from polycarbonate

Tuesday evening was another busy evening at the makerspace with a lot going on and a couple of people visiting the space. It’s even possible that a theme emerged for the evening, which seems to have been the letter ‘P’.

Plans were hatched (including some for the Always The Sun festival in September), Phones were prodded, Polycarbonate was lasered, Prototype development boards were Programmed, and Pudding (okay technically a huge slab of brownie from Smokey Joe’s) was purchased.

The image at the top of today’s post shows a dress repair project (which is where the polycarbonate comes in). A new plastic strap slider thingumy was needed and they’re not something you can easily buy in small numbers.

As you can see the end result worked, but does look a little charred. Polycarbonate seems very smokey to cut, even having refined the setting to use two passes (85% power, 80mm/s). Dropping the power lower may help a bit for future attempts.

Anyway you can find out more about some of the plans (including raft building and non-planar video projection) on our Forum, or by dropping by. If you’d like to find out more about the brownie then I’d suggest coming to one of our Tuesday or Friday Open Sessions and stopping at Smokey Joe’s in the garden downstairs first.


Cool Storage Solutions

It was another busy (but fortunately not so oppressively hot) night at the Makerspace this Friday.

There were new visitors to the space, laser cutting of parts for a camera mount, some rather mis-aligned bearings, some ongoing sewing, and some new storage since last week!

Matt managed to get us some small wall mounted storage boxes at a knock down price.

Better yet (at least for anyone who doesn’t like their chocolate in a puddle) he’s also lent the space a small peltier based fridge!


Droning, Drilling and Chilling

Our open evening on Friday was another bustling one if a little on the warm side.

Sadly even with all its motors replaced this little drone didn’t seem to make enough of a breeze to help.

The evening also included some tidying of the Makerspace’s inventory, a new visitor to the space, and an attempt to drill out some security screws.

“But what of the oppressive heat?” you ask, why didn’t it bring the space to a halt?

Never fear, for where there’s a spare air blower for the laser cutter there’s a way!

Will the entire contents of the space have been blown out of the window?  What further adventures in improvised climate control are on the horizon?  – Come along to one of our open evenings to find out the answer to these (and possibly even some useful) questions.


[Learning Series] – Making a widget case, from start to finish – part 1


Hello! This will be a first, experimental post in a little series of blog posts detailing a complete workflow – hopefully useful to someone who might be wanting to use the laser cutter or work on a small project.
Recently, I’ve been playing with our space’s laser cutter with a couple of simple projects. My most recent was a branded flyer holder for Innovate Guildford, a recent event we attended – which came out great!

Fig 1: The finished stand – I really liked the aesthetic and simple assembly of this guy.

My first eyeballed design of the stand – done in Fusion 360, my CAD software of choice – would tip backwards with a light touch. It was also quite a tight fit, which required a visit from a persuader to assemble everything correctly. I quickly edited the design in F360 and made the side panels extend behind more to give a bit more support, and changed the kerf adjustment size from 0.3mm to 0.15mm (kerf is the size of the laser beam, and adjusts your design accordingly – a simple rule of thumb is a smaller kerf adjustment = looser fit).

This was the thing that really cemented the usefulness of the laser for me – a quick design change, set up the laser, make the cut, and replace the side panels took all of 5 minutes to do. Try that design change on a 3D printer, and you’ll be waiting a while.

The result was nice too – it fit together much more smoothly thanks to the kerf adjustment, the simple engraving on the front adds a touch of custom flair, and of course, it performed its job of holding our flyers very well.

Going from start to finish like this isn’t quite as hard as it seems. Neither is Fusion 360. In this little series of blog posts I’d like to approach something a little more complicated, which is to make a laser cut case for a small electronic widget – the Bus Pirate.

What’s a Bus Pirate?

Fig 2: Bus Pirates on a Pirate Bus – not what we are dealing with today.

No, not that. A Bus Pirate is a very handy little gizmo for electronics work – designed by Ian Lesnet and produced through Dangerous Prototypes. A simple look at the BP shows that its main purpose is for talking to electronics over a variety of protocols, such as I2C, SPI, 1-Wire, JTAG, MIDI etc. It can also act as a power supply, logic analyser, oscilloscope, ICSP programmer, and really, anything you might want to do with interfacing your computer to a component or circuit.

Fig 3: An actual Bus Pirate – v4 in this case.


I own one of these guys – specifically, the V4.0 version, and admittedly I have used it a handful of times – I’m simply not that good enough at electronics (yet!) to have needed it. However, when I do, I can reach for it with confidence that it will help me out.

Currently, the BP sits in a component box alongside it’s probe lead, a cheap Chinese logic analyzer clone, and some other bits and bobs. While I’m sure the PCB, with it’s mostly low profile SMD components, will be relatively safe from harm if I transported it separately, there is something reassuring and polished about having it in its own case – hence the start of this project.

Case features

As always, it’s good to start out with a few objectives, or specifications, before we even start designing. Let’s define what I want this case to provide and why:

  • Made from laser cut acrylic. Acrylic is nice, easy to cut, pretty cheap, and colourful. There’s a plethora of material options available, and I’ve used it already.
  • Cutouts for the business parts. There’s a mini-USB connector, the 12 pin shrouded connector for the probes, and an ICSP pin header. Access to these is the main function of the board, so it would be pretty daft to make them unusable. We need to bear in mind the sizes of the relevant connectors that will be plugged in to them.
  • Visibility of the 4 status LEDs on the top. The LEDs are coloured, and while easy to distinguish their function from their location, it might be nice to make them easily visible with uncoloured, clear acrylic.
  • Button pushes. There’s two buttons on the board, ‘Normal’ and ‘Reset’. Limiting access to these will always lead to frustration some day, so we could either add small holes for access for a pokey thing (technical term), or include some parts in our design to extend the buttons to the surface.
  • Labelling – engraved labels for the LEDs, buttons, and even pinouts would be very useful. The main connector takes a colour coded probe lead. If we can somehow add the colour codes for quick and easy identification, this would be very handy.
  • Sturdy – I’m not saying this will be subjected to abuse, but it’s reassuring to know that it can take a few hits.

We’ll likely add more and take some out, and even iterate over the design, but before diving in it’s always worth taking our time to spec our design out and have some goals in mind.


Because we’re designing a case for an existing thing, it makes sense to get an accurate reference design of it as our first task. Sure, the flyer stand had this – we needed to know how big an A5 flyer was, to make sure it did its one main function properly – holding them! This wasn’t a hard task to accomplish, but our Bus Pirate is slightly more complex. We have the board size, mounting holes, LED positions and of course those connectors to deal with.

We have a few options of how to approach this. We could reach for our vernier calipers and measure everything up – or we can cheat, which is what I like the sound of. Being open source hardware, Dangerous Prototypes allow us access to all the design files. In this case, the board designs are in Eagle format – not my preferred choice (KiCad 4 lyf <3), but free and easy to install.

Now this next part took a lot longer than expected. There are a few options out there for taking an Eagle .brd file and getting some designs out of it – exporting to DXF, for example. There are promises of “easy” Eagle to Fusion 360 workflows, where the board and its components are sent over as a 3D model. Sadly this didn’t work – neither did exporting to KiCad, and some other things.

Fig 4: Flat board at first – adding heights in for each component is easy though.

What did work for me was a nifty website,, which will happily take an Eagle .brd file and spit out a .STEP file. This wasn’t without problem, as all the components had no height thanks to (I think) it being an old version of Eagle. Thankfully the web interface made it easy to set the heights of the important components, and as it was late and I was feeling lazy this would do for my purposes. Looks like I will be using those calipers after all.





Fig 5: This only took a couple of minutes.

A few clicks later and editing the depths wasn’t nearly as hard as I thought it’d be. I measured the important components (connectors, switches, and LEDs) and guesstimated the rest. Thankfully the interface recognises all component shapes/packages of the same kind would have the same height, so you only have to enter the custom height in once for each package type.

For me, this is good enough for our design – all the important stuff is preserved and is more or less accurate.

A few more clicks, a bit of a wait for processing time, and I have a .STEP file of the Bus Pirate based off the actual board design.


Fusion 360 Beginnings

First off, let’s create a new project – a container that represents all of the files related to our case design. Even after using F360 for a few months, I’ve ended with reams of files and have found the cloud-based project approach refreshing.

After creating a project, I can click File > New Design From File and import our new .STEP file to create a component. Nothing exciting to say here – it took a few seconds to import while F360 thought about things, and it appeared. A slight mishap is that the mounting holes are filled in, I think because they were considered components in ecad. Not a problem though as the mounting hole is still there and selectable, and that’s all we need.

A quick test with the Inspect tool (shortcut ‘i’) confirms that the board is the same size as the one in my hand.

Fig 6: imported into F360 and looking good.










That’s it for part 1! In part 2, we’ll start designing the case from the imported board model, keeping in mind our design specs. Stay tuned for more 🙂


SHM 3D Printer Filament Store and Dispenser

This is a direct copy of a SHM forum post, which can be found here . If you’re interested in what we do or would like to share a project of your own with us, please take a look at the forum here


SHM Filament Store and Dispenser
Having finally got our 3D printer into a workable state it needed a permanent home, rather than just perching on a surface stealing valuable bench space. So we decided to put in into one of our large storage units. Great idea you say ! Of course you are right, but how on earth do we store and smoothly feed filament to the printer from the large 2 kilo reels of 3mm PLA that were kindly donated to us?

Our solution of choice was to put the reels outside of the cabinet, thereby minimising the loss of shelf space.

Being of a parsimonious mindset we looked around the SHM Makerspace to see what materials might be utilised for the build.

Filament Dispenser Brackets
These were made from some offcuts from our Reuleaux triangle stool build, which itself was made from laminated discarded ply. The ubiquitous all purpose offcuts of plastic plumbing pipe from the geodesic dome build were used as spindle holders. The pipe fits snugly into a 34mm hole drilled into the edge profile of the shelf support.

Filament Feed Through
We designed a parametric feed through tube1 and mounting in openSCAD to allow the filament to pass through the cabinet wall, the tube angle was set at 30 degrees to the mounting axis. Two of them were produced on the SHM Makerspace printer and bolted together through the cabinet side.

Each bracket was mounted on the side of the storage unit with a pair of screws.

The spindle to hold the filament was an old piece of pine curtain rail, complete with a fine finial, reclaimed from the original space conversion.

Shelf feed and installation
The final step is to feed the filament through the shelf to the printer. For the moment we’ve just drilled a hole in the storage shelf above the printer until we work on a design for a 30 degree overhang feeder tube.